Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Tarzana
Gate parts and welding in Tarzana usually comes down to one of three things: a hinge that finally gave out, a post that’s rusted through at the base, or a panel that needs a welder who actually shows up with the right rig. We handle all three, and we do most of the work right in your driveway. If you’re south of Ventura Blvd on one of the hillside lots, you already know the heat and Santa Ana winds don’t treat iron gates kindly. Hal Gatewood has been fixing gates since 2001, and he still answers the phone himself. Call (323) 677-4063 and you’ll get a straight answer about what’s wrong and what it’ll cost before any work starts.
Why Gatewood Fence & Gate Is Tarzana’s Preferred Gate Parts & Welding Company
We’re not a faceless outfit running a call center three states away. Gatewood Fence & Gate is locally owned and owner-operated, and Hal Gatewood’s name is on the shop and on every invoice. That matters in Tarzana, where a gate that won’t close properly isn’t just an annoyance - it’s a security gap on a property with a long driveway and maybe a hillside exposure behind the house. We publish our address and license number. You can look us up, or you can drive to the shop and look Hal in the eye.
Our crews know the difference between a 1970s ranch gate north of Ventura and a custom ornamental iron gate on a 1980s estate south of it. That’s not trivia - it changes which parts we stock on the truck, how we approach a weld, and whether we flag an LAFD compliance issue before it becomes an expensive surprise. Tarzana customers call us because the person who shows up understands what they’re looking at. And because calls are answered by a live person, 24/7, not a voicemail that might get returned next Tuesday.
Every job carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings Hal back. No runaround, no fine print.
Our Gate Parts & Welding Services in Tarzana
This is the work we do most often in Tarzana, and each one has its own local failure pattern. Here’s what we see and how we handle it. Our Gate Parts & Welding team carries the common weldments, hinge stock, and hardware for most repairs, but custom work gets measured and fabricated properly, not guessed at.
Hinge Replacement
Santa Ana winds don’t just rattle gates - they strip hinge pins and bend the strap hinges on older swing gates, especially on hillside properties where a gate catches the wind like a sail. A typical hinge replacement on a Tarzana residential gate runs $180-$400, depending on whether it’s a barrel hinge on a light pedestrian gate or a heavy weld-on strap hinge on a full driveway swing gate. We cut off the old hinge, true the panel, and weld the new one in place so it doesn’t bind.
Post Replacement
A gate sags in the hinge post, not in the middle - and that’s where we start. In Tarzana, the classic failure south of Ventura is a post that rusted through at ground level after thirty years of irrigation splash and clay soil holding moisture against the steel. Post replacement typically runs $450-$900 here, which includes cutting out the old post, pouring a new concrete footing, and setting a new steel post plumb. Fix the panel without the post and you’ll fix it twice.
Rail Repair
Bottom rails and mid rails on older tubular-steel gates corrode from the inside out, especially on Tarzana’s older 1970s and 1980s stock where the original paint has long since given up. A rail repair or replacement usually costs $200-$500 depending on the length and whether we’re splicing in new square tube or welding angle stock. We match the existing profile so the repair doesn’t look like a patch job.
Custom Welding
When a gate is beyond a patch, or when a homeowner wants a heavier, better-built replacement that matches the house, we custom fabricate on site. Our crew got called to a hillside property off Vanalden Avenue where a 1980s single-swing iron gate had sagged so badly it was dragging across the driveway. The hinge post had rusted through at the base - a classic Tarzana failure - so we cut out the old post, poured a new concrete post footing, and welded on a heavier hinge while converting the setup to a slide gate with a rack and pinion drive and a Knox box to satisfy current LAFD response-time standards. That’s the difference between a parts swap and a real fix. Custom welding work in Tarzana typically runs $600-$1,800 depending on the scope, and we always quote the number before striking an arc.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Tarzana
We’re certified to service nine major gate brands, but in Tarzana we see a lot of LiftMaster, FAAC, Mighty Mule, and BFT operators on these driveway gates. The 105°F-plus summer heat in the Valley bakes wiring insulation and burns out motors faster than coastal installs, so if your LiftMaster is cycling oddly or your FAAC operator stopped responding, it’s not just old age - it’s Tarzana’s climate doing what it does. We keep common parts for these brands on the truck, which means fewer trips back and forth for you. And because we work on them every week, we can usually diagnose the problem in the first fifteen minutes on site.
Common Gate Parts & Welding Problems We See in Tarzana Homes
- Wind-thrown swing gates: Santa Ana gusts tear through the Valley and knock aging single-swing gates off their hinge alignment. The hinge pin strips or snaps, the gate twists, and suddenly it’s dragging across the driveway. We re-align the panel, weld in new hinges, and re-set the post if needed.
- Heat-baked operator electronics: Tarzana’s summer heat bowl pushes ambient temps over 105°F routinely, and that bakes the wiring insulation inside gate operator enclosures. We replace burned-out LiftMaster and FAAC control boards and motors far more often here than we do in cooler coastal zip codes.
- Rust-through at post bases: The clay soil south of Ventura holds irrigation moisture against steel posts for years. We regularly see posts that look fine above ground but have rusted through entirely below the surface. That’s why we quote post replacement with a new concrete footing, not a wrap-and-hope patch.
- Single-swing gates that can’t pass LAFD rules: Hillside estates in the Very High Fire Hazard Severity Zone have gates sized for one car and an operator that can’t reopen fast enough to meet current emergency response standards. A simple repair call often becomes a slide-gate conversion, which is exactly the kind of work we specialize in.
Pricing for Gate Parts & Welding in Tarzana, CA
Here’s what we charge in Tarzana, in real numbers. Hinge replacement runs $180-$400. Post replacement is $450-$900. Rail repair is $200-$500. Custom welding jobs run $600-$1,800 depending on the fabrication work. A full slide-gate conversion with a Knox box and battery backup starts around $2,800 and goes up from there based on gate length, driveway width, and operator choice. Every estimate is quoted and agreed before any work starts - the number on the invoice matches the number we gave you. We also have standing offers that don’t require haggling: $40 off any repair over $200, a free second opinion on any written estimate, and no trip charge inside the county. Seniors and veterans get a permanent 10% discount. Call (323) 677-4063 and Hal will give you an honest figure over the phone.
We Also Serve Cities Near Tarzana
We’re based in the Los Angeles area and our crews serve Tarzana locally, but we also take calls from Encino, Sherman Oaks, Van Nuys, and Studio City. If you’re in one of those areas and dealing with a gate that won’t close or a post that’s leaning, call the same number - (323) 677-4063. Read more about our Gate Parts & Welding in Tarzana coverage and what we see in this part of the Valley.
Serving Tarzana, CA - Our Local Coverage Area
We’re based in the Tarzana area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Tarzana
Because those hillside estate gates were built in the 1980s to swing open for a single car, and they can’t reopen fast enough to meet current LAFD emergency response standards. South of Ventura Blvd, the Very High Fire Hazard Severity Zone rules require automated driveway gates to have a Knox key switch, battery backup, and a reopening speed and clearance width that old single-swing iron gates simply can’t provide. So a hinge repair becomes a slide-gate conversion with a rack and pinion drive. It’s a bigger job, but it’s the only way to be code-compliant. Call (323) 677-4063 for an estimate on a slide-gate conversion - the quote is free.
Santa Ana winds hit hillside properties south of Ventura hard, and a swing gate that faces the wind acts like a sail. The repeated gusting strips hinge pins, bends strap hinges, and torques the post until the concrete footing starts to crack. We see this every fall and winter in Tarzana. The fix is usually a heavier weld-on hinge and, if the post has moved, a new concrete footing. A hinge replacement with post re-set typically runs $450-$900 here. Call (323) 677-4063 and we’ll tell you what your gate needs before the next wind event.
In the Very High Fire Hazard Severity Zone south of Ventura Blvd, LAFD requires automated driveway gates to have a Knox key switch for fire department override, battery backup so the gate opens during a power outage, and a reopening speed and clearance width that meets emergency vehicle access standards. Many older gates in Tarzana fail at least one of those requirements. We handle the compliance work as part of gate replacement or conversion, not as an afterthought. Call (323) 677-4063 for a free estimate on bringing your gate up to code.
Because the panel is rigid - the post is what’s taking the load. Steel posts in Tarzana’s clay soil rust at the base where irrigation water sits against the metal year after year. The panel itself is usually fine; the post just gave up. That’s why we always check the post before quoting a hinge replacement. A post replacement with a new concrete footing runs $450-$900 and fixes the problem permanently. Call (323) 677-4063 and we’ll come look at your post for free.
After any welding or repair that touches the gate frame or operator, UL 325 requires functioning entrapment protection: photoelectric sensors, reversing edges, or a proven obstruction-sensing operator. If your gate has an older operator without these, we’ll flag it during the repair. Count on us to tell you what’s required and what it costs - no surprises. Call (323) 677-4063 for a free assessment of your gate’s entrapment protection.
Contact Gatewood Fence & Gate in Tarzana
If your gate is sagging, dragging, or refusing to open, call (323) 677-4063. Hal answers the phone himself, 24/7. You’ll get a straight answer, an honest price, and a real person who stands behind the work - with the name on the shop and the shop down the road.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Tarzana since 2001.