Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Van Nuys
Gate parts and welding in Van Nuys comes down to one thing: the heat. That’s our starting point on every call in this part of the Valley. When your swing gate sags, a slide gate jumps its track on a 108°F afternoon, or a Lo-Swing motor strips for the third time in two summers, the fix usually lives deeper than the part that failed. We’re Gatewood Fence & Gate, and our Gate Parts & Welding team has spent years tracing Van Nuys gate failures back to their real source: heat-weakened welds, retrofitted posts that were never deep enough, and operators running past their rated duty cycle every single afternoon. Call (323) 677-4063 and we’ll tell you straight whether that gate can be welded back to solid on site, or whether you’re throwing money at a motor that was already cooked.
Why Gatewood Fence & Gate Is Van Nuys’s Preferred Gate Parts & Welding Company
Hal Gatewood started this company in 2001, and he still answers the phone. That matters in Van Nuys, where homeowners have been burned by outfits that quote one number over the phone and send a different one with the invoice. We publish our address, our license number, and Hal’s name goes on every job we do. If a weld fails or a hinge we replaced starts to sag, the 90-Day Done Right Promise is in writing, not buried in fine print. One call brings Hal back.
Our customers here run from the ranch houses off Vanowen and Victory to the apartment complexes and industrial yards near the airport, and they rely on our Gate Repair in Van Nuys when problems arise. We know those streets. We know the gates on them. And when someone near Sepulveda and Burbank calls about a gate that won’t close, we know before we arrive that we’re probably looking at a 1980s operator that’s been running hot for thirty years, not a rust problem like you’d find near the coast.
Response time to Van Nuys is measured in the time it takes to get from the 101 or the 405 into your driveway, not in dispatch windows. Gate Parts & Welding in Van Nuys is local work for us, and we treat it that way.
Our Gate Parts & Welding Services in Van Nuys
Hinge Replacement
Hinges fail first on Van Nuys gates. That’s not an accident. A steel swing gate hanging off two hinges on a 1950s ranch property has been absorbing valley floor heat every afternoon since it was bolted on, often thirty or forty years ago. We see hinge pins worn to half their diameter, weld joints cracked through from repeated expansion, and post plates that have pulled loose from the concrete. We cut out the old hinge, weld in a new one rated for full gate weight, and set it so the gate rides true. Hinge replacement in Van Nuys typically runs $180 to $400 per hinge depending on gate weight and condition of the post.
Post Replacement
A gate sags in the hinge post, not in the middle, and that’s where we start. Van Nuys is full of posts that were set shallow in the 1980s, before anyone thought much about gate weight or wind load, and proper Gate Installation - Van Nuys standards now require much deeper footings. Years of Santa Ana wind events have worked those posts loose in the soil. We dig out the old footings, set new posts at proper depth, weld the hinge plates square, and the gate hangs like it should. Post replacement in Van Nuys usually falls between $500 and $1,200 per post, including concrete and hardware.
Rail Repair
Slide gate rail failures in Van Nuys follow a pattern we can almost set a watch by. Steel rails expand in the heat, the gate climbs or binds, rollers break, and the thing jumps its track. On the commercial stretch along Saticoy and Stagg near the airport, those high-cycle cantilever gates run all day in the worst thermal environment in the county. Rail repair means straightening or replacing the v-track, resetting rollers, and often welding in a fresh section where the old rail wore thin. Expect $350 to $900 for residential rail repair, more for commercial systems with high-tonnage gates.
Custom Welding
Some Van Nuys gates can’t be saved with a replacement part from a catalog. The panel is bent, the mid-rail is cracked, or the pickets are pulling loose from the frame. That’s where on-site welding comes in. We don’t haul your gate to some shop across the city. We weld it in your driveway, reinforced at the stress points, with heat-sized gaps that let the metal expand on 110°F afternoons without popping the paint or cracking the weld. Custom welding jobs in Van Nuys run from $150 for a small crack repair to $800 or more for full frame straightening and reinforcement.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Van Nuys
We carry parts and service support for the operators Van Nuys actually has: Lo-Swing retrofit systems, older Linear units from the 1990s, Mighty Mule openers on ranch gates, plus newer LiftMaster and FAAC equipment. We stock common control boards, capacitor kits, photo-eyes, and hinge hardware locally, which means we’re not waiting a week on a freight shipment when your gate won’t close. If you’re running a brand we don’t stock parts for, we’ll tell you that on the phone, and we’ll tell you what it costs to retrofit to something supported.
Common Gate Parts & Welding Problems We See in Van Nuys Homes
- Heat-killed motors and control boards. Valley floor temperatures hit 105-110°F for weeks every summer. Capacitors and circuit boards inside operators fail far faster than their ratings suggest. We replace failed boards and often add ventilation or a heat shield so the next one survives.
- 1980s Lo-Swing and Linear systems hitting end-of-life at the same time. Van Nuys has a concentrated pool of retrofit-era gates, most installed between 1985 and 1995 on ranch homes and 1970s apartment buildings. They’re all aging out now, which is why so many neighbors on the same block suddenly have the same failure.
- Heat-expanded steel gates jumping their tracks. Steel slide gates expand in prolonged heat. If the rail was installed tight, the gate climbs the v-track and drops a roller. We see this weekly on the light-industrial gates around Woodley and Vanowen.
- Santa Ana wind damage to swing gates. Unsecured swing gates take a beating during fall wind events. Years of heat-weakened welds plus one strong gust equals a bent hinge post and a stripped motor. We repair the post, reweld the hinges, and add positive stops so it can’t happen the same way twice.
Pricing for Gate Parts & Welding in Van Nuys, CA
Here’s what we actually charge in Van Nuys, no phone quote games. Hinge replacement runs $180 to $400 per hinge. Post replacement runs $500 to $1,200 per post, dug and set to proper depth. Rail repair runs $350 to $900 for residential, with commercial slide gates on the airport corridor typically running higher due to gate weight and cycle count. Custom welding starts at $150 for a crack repair and goes up to $800 or more for full frame work. Every single job gets a written price before we start, and that’s the number on the invoice. No trip charge inside the county. Free second opinion on any written estimate. $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Call (323) 677-4063 for an exact quote, estimates are free, and Hal will give you the straight answer.
We Also Serve Cities Near Van Nuys
From our Los Angeles office, we cover the neighborhoods around Van Nuys and the surrounding communities: Sherman Oaks, Studio City, North Hollywood, and Encino. Same straight pricing, same 90-Day Done Right Promise, same owner answering the phone at (323) 677-4063.
Serving Van Nuys, CA - Our Local Coverage Area
We’re based in the Van Nuys area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Van Nuys
Van Nuys sits in the deepest part of the San Fernando Valley heat basin, where summer temperatures run 15-20°F hotter than communities on the other side of the hills. A gate operator in Sherman Oaks might peak at 90°F on a bad day. In Van Nuys, the same unit cooks at 110°F for hours, which is why Van Nuys Gate Motor & Opener service is so critical. That heat kills capacitors and control boards far faster than manufacturer ratings assume. The fix is often a hardier board or a heat shield, not another identical motor. Call (323) 677-4063 and we’ll tell you what’s actually dying.
Usually yes, if the post is still solid. We replaced the hinge posts on a 1980s Lo-Swing swing gate at a ranch home off Vanowen where decades of Santa Ana winds had stripped the motor and sag correction alone couldn’t fix the post footings. The control board was still original but the safety photocells hadn’t worked in years, so we retrofitted a new UL 325-compliant photo-eye set and welded fresh post hinges. That gate is running today. If your post is rotted or the frame is bent beyond straightening, we’ll tell you replacement is cheaper than repair, and give you the actual numbers. Free estimates, always.
Yes, if you have an automated gate that was installed before the current safety standards. Modern code requires entrapment protection, which means working photo-eyes or another listed safety device. Many Van Nuys gates from the 1980s and 90s either never had them or the originals failed years ago. We retrofit UL 325-compliant photo-eye sets on older systems as standard practice. It’s a safety requirement, not an upsell. We won’t leave a gate running without it.
Steel expands when the temperature climbs, and Van Nuys heat is extreme. If your rail was installed without enough expansion clearance, the gate grows in the heat and climbs the v-track, breaking rollers and stressing the rack and pinion. On the light-industrial gates near the airport along Stagg and Saticoy, this cycle repeats every summer. The permanent fix is resetting the rail with proper expansion gaps and replacing worn rollers. That’s rail repair work, typically $350 to $900 on a residential gate. Call us before the gate comes off the track entirely.
We repair Lo-Swing and Linear retrofit operators, Mighty Mule, LiftMaster, and FAAC systems, among others. If you’ve got a 1990s Linear operator that’s failing, we can usually source the board or retrofit the drive. If it’s a brand nobody supports anymore, we’ll tell you on the phone, and quote you a retrofit that makes sense rather than patching something that fails again in August. Call (323) 677-4063 and Hal will give you the straight answer.
Ready to get that gate fixed for good? Call Gatewood Fence & Gate at (323) 677-4063 for free estimates on gate parts and welding in Van Nuys. Hal answers the phone, the price is written down before work starts, and every job carries the 90-Day Done Right Promise.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Van Nuys and the San Fernando Valley since 2001.