Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Culver City
Gate installation in Culver City means working with a building department that has its own rulebook, a marine layer that eats unprotected steel, and blocks where a 16-foot swing gate shares a driveway easement with your neighbor. We know that because we work these streets every week. If you need a driveway gate, pedestrian gate, sliding gate, or security gate installed in Culver City, call (323) 677-4063 and you’ll get Hal or someone on his crew, not a voicemail. We price the job before we start, and we don’t change the number at the door.
Why Gatewood Fence & Gate Is Culver City’s Preferred Gate Installation Company
Gatewood Fence & Gate has been locally owned and owner-operated since 2001. Hal Gatewood’s name is on the shop and on every invoice. When you call about Gate Installation, you’re talking to the person who will show up, measure, and weld on site if that’s what the job needs. We don’t haul your gate to some offsite facility and we don’t swap parts that still have life in them.
Culver City homeowners deal with specific headaches: tight setbacks, shared rights of way, coastal corrosion, and a permit office that will hand you a stop-work order if you filed under the wrong city’s code. We’ve worked through those headaches for years. Assignments are coordinated from our Los Angeles office, and our crews serve Culver City locally. When a gate goes down on a Saturday evening, someone answers the phone and someone shows up.
Our Gate Installation Services in Culver City
Driveway Gate Installation
A new driveway gate on a 1920s Spanish Colonial in the flatlands usually means the existing posts and footings were never built for an automated operator. We install the gate and, when needed, the footing and post work that makes it safe under motor load. If the driveway slopes, we account for that before we order hardware, not after the gate binds on day one.
Pedestrian Gate Installation
Pedestrian gates in Culver City are often original ironwork from the 1930s and 1940s, which means the hinge posts are embedded in old masonry piers. We install new pedestrian gates with post hardware rated for coastal air, and we match the look of the existing property. No vinyl-coated tubing that looks wrong on a Craftsman bungalow.
Sliding Gate Installation
Sliding gates are the right answer for most Culver City homes with a short driveway apron, because a swing gate needs 3 feet of setback from the property line when it opens outward. We install cantilever and v-track sliders on new steel posts, and we spec track and rack components that handle marine-layer corrosion. This is the service we recommend most often on tight lots east of Sepulveda.
Swing Gate Installation
Swing gates work on wider properties west of Overland Avenue, where there’s room for a proper opening arc. We fabricate and install single and double swing gates, set operators like FAAC and Linear, and run safety edges and photocells to meet UL 325 requirements. Every swing gate gets a physical stop and a locking point that won’t rattle in Culver City’s evening breeze off the ocean.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Culver City
We’re certified to service nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Culver City specifically, we keep FAAC, BFT, and Linear operator parts in stock because those are the units we see on most local installs. That means less waiting when a board fails on a Monday morning. If your existing gate has a different brand, we still service it, and we’ll match the replacement to what your property already uses.
Common Gate Installation Problems We See in Culver City Homes
- Wrong-city permits: A contractor files under LA City code instead of Culver City’s Building Safety Division, and the job gets a stop-work order. Culver City requires a 3-foot minimum setback for an outward-swinging driveway gate from the property line, not LA’s 5-foot rule. We pull the right paperwork the first time.
- Marine-layer corrosion on slide tracks: A new sliding gate gets a rack and pinion rated for inland use, and within two years the salt air has eaten the rack teeth. We install corrosion-rated rack and track for every Culver City slide gate, and we tell you what to lubricate and when.
- Hayden Tract commercial gates binding on standard tracks: The architect-designed creative offices along Washington Boulevard and the Hayden Tract have automated sliding gates with odd header clearances and non-standard track lengths. A stock trolley track often ends up 2 inches too long, and the gate binds on the first cycle. We measure, then order or fabricate to spec.
- Old masonry piers failing under new operator torque: A 1940s wrought iron driveway gate gets a modern operator bolted to a pier that was never built for that load. The pier cracks, the gate sags, and the operator burns out. We check the post and footing before we mount anything.
Pricing for Gate Installation in Culver City, CA
Gate installation prices in Culver City run higher than Burbank or Pasadena because of local permit requirements, coastal-grade hardware, and the amount of site work older properties need. A basic pedestrian gate installation typically runs $900 to $2,400. A single swing driveway gate with an FAAC or Linear operator runs $3,800 to $7,200, including posts and wiring. A sliding gate, especially on a slope or with a long track run, runs $4,500 to $9,500. Security gates with heavier steel and access control push toward $8,000 to $15,000. Every quote is written and agreed before work starts, no change at the door. Call (323) 677-4063 for a free estimate. We’ll measure, walk the site with you, and put the number on paper.
We Also Serve Cities Near Culver City
Most of our Culver City work comes from homeowners who found us through neighbors, and we regularly run jobs in the surrounding westside cities. If you’re in Marina del Rey, Beverly Hills, Santa Monica, or West Hollywood, the same crew and the same pricing applies. Culver City is our anchor, but we’re on these roads every week.
Serving Culver City, CA - Our Local Coverage Area
We’re based in the Culver City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Culver City
Yes. Culver City’s Building Safety Division requires a permit for replacing an automated gate operator on an existing driveway gate when the operator changes the gate’s operation or safety systems. The electrical work also falls under the city’s permit requirements. This is the single most common stop-work trigger we see, and we handle the permit before the first tool comes off the truck. Call (323) 677-4063 if you’re unsure, and we’ll tell you what’s needed for your specific address.
Marine air. Culver City sits roughly four miles from the Pacific, and the persistent marine layer carries salt that corrodes uncoated steel track, rack teeth, and operator mounts far faster than the drier inland air of Burbank. A slide gate that would run 10 years in Burbank can show rack tooth wear inside 24 to 36 months here. The fix is simple: install corrosion-rated rack and track, use greasable bearings, and schedule annual lubrication. Call (323) 677-4063 for an exact quote. We’ll spec the right hardware the first time.
Yes, and we do it often. Shared driveways in Sunkist Park typically run along a narrow right of way with two homes behind one apron. Culver City requires a 3-foot setback from the property line when a gate swings outward, so on many shared driveways we install a sliding gate instead, which uses zero swing arc. If a swing gate is feasible, we run safety photocells and edge sensors so the gate stops if a car or person is in the path. The exact layout determines the right approach. Call (323) 677-4063 and we’ll walk the driveway with you.
Usually, yes. The gates themselves are often salvageable and worth keeping. The bigger issue is what they’re hung on: the original hinge posts and masonry piers from the 1940s were never built for a motor’s torque. We evaluate the post, the footing, and the gate’s total weight before spec’ing an operator. If the footing needs replacement, we pour it, hang the original gate on new hardware, and mount the operator. The gate keeps its character, and the system works like new. Call (323) 677-4063 to schedule a free walkthrough.
Those gates are custom-built for shallow header clearances and non-standard track lengths, and they were often installed on tight industrial parcels with very little room to work. A standard trolley track or off-the-shelf operator mount frequently doesn’t fit without binding. We measure on site, order or fabricate components to match, and schedule the work so the gate remains functional while we install. That’s a different job than a residential driveway gate, and it’s work most residential-only gate companies won’t take. Call (323) 677-4063 for a site evaluation.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Culver City since 2001.