Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Beverly Hills
Gate installation in Beverly Hills is rarely a simple swap. The city runs its own Building & Safety Department, separate from Los Angeles, so even a like-for-like operator replacement needs a permit through Beverly Hills City Hall. Most homes here sit behind ornamental iron gates from the 1920s through 1940s, hung on original brick or stone pilasters that standard hardware won’t fit. We know that before we ever set foot on your driveway. Hal Gatewood has been doing this since 2001, and when you call (323) 677-4063, a live person answers. No voicemail, no call center. Just us, and we’ll tell you straight what your gate needs.
Why Gatewood Fence & Gate Is Beverly Hills’s Preferred Gate Installation Company
We’re not a national outfit running crews through Beverly Hills between jobs in other counties. We’re locally owned and owner-operated, and Hal’s name is on the shop and on every invoice. That matters when your gate has to pass architectural review and survive Trousdale grades. The person who shows up is someone you can find again at the hardware store or the shop down the road.
Beverly Hills customers call us because we answer the phone at 2 a.m. and because our 90-Day Done Right Promise is stamped in writing on every job. If something isn’t done right, one call brings Hal back. No runaround. We also offer a free second opinion on any written estimate, no trip charge inside the county, $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. Those aren’t haggling points. They’re standing offers.
Our crews are background-checked and uniformed. We’re certified on nine major gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. More important for Beverly Hills, we understand the permitting path through City Hall and we coordinate with HOA management companies before the first hole is drilled. That keeps your project moving instead of stalled at a review board.
Our Gate Installation Services in Beverly Hills
Every gate we install in Beverly Hills starts with the approval reality, then the work. We also weld on site, so your gate stays in your driveway instead of getting hauled off to some shop you’ll never see. Here’s what we handle most.
Driveway Gate
A driveway gate in Beverly Hills is usually a statement piece. We build and install custom ornamental iron, steel, and wood driveway gates sized to your opening and your architecture. On hillside lots north of Sunset, we account for slope, wind load, and drainage before we ever pour a footing. A gate that looks beautiful but binds on a grade isn’t installed right. We do it right the first time.
Pedestrian Gate
Pedestrian gates here often match a main driveway gate, and that means matching century-old ironwork. We fabricate on site when stock parts won’t do. The hinge post is the most common failure point on older pedestrian gates, especially on original masonry. We reinforce the post, not just the panel. If you fix the leaf and ignore the post, you’ll need Gate Parts & Welding in Beverly Hills to fix it twice.
Sliding Gate
Sliding gates fit tight Beverly Hills driveways where a swing gate would eat too much space. On Trousdale slopes, we spec high-torque operators with grade-compensating brakes, because flat-ground motors burn out fast climbing 15-20% inclines. We also install Beverly Hills Gate Access Control systems with loop detectors and safety photocells so the gate never closes on a car or a person.
Swing Gate
Swing gates are the classic Beverly Hills style, especially on the Spanish Colonial and Tudor estates south of Santa Monica Boulevard. Those gates are heavy by design, and the original brick or stone pilasters often can’t accept standard hinge posts. We use masonry-specific anchoring and custom forged hinges sized to the load. The gate swings true without stressing century-old brick.
Trusted Brands We Service in Beverly Hills
We’re certified to service and install nine major gate brands, and we stock parts locally for the ones Beverly Hills homeowners actually have: LiftMaster, FAAC, BFT, and Mighty Mule. If your operator is acting up, we likely have the part in hand for same-day Gate Repair in Beverly Hills. If it’s an older model nobody stocks parts for anymore, we’ll tell you that too, and we’ll give you options. We don’t swap parts that don’t need swapping. Hal fixes the gate in your driveway rather than hauling it off or selling you a replacement you don’t need.
Common Gate Installation Problems We See in Beverly Hills Homes
- Architectural review denials. Beverly Hills HOAs and the city’s architectural review board reject gate styles, heights, and finishes that weren’t pre-approved for the neighborhood’s Spanish Colonial or Tudor character. We submit designs that match the existing streetscape, so you don’t burn a permit cycle on a rejection.
- Operator burnout on Trousdale driveways. A slide gate motor spec’d for flat ground gets installed on a steep grade and runs hot until it dies. We upgrade to high-torque operators and install a grade-compensating brake, a detail that rarely comes up two miles south in the flats.
- Hinge post failure on original masonry. The 1920s-1940s brick or stone pilasters weren’t built for modern gate loads. Within months, the gate sags and scrapes. We reinforce the pilaster with masonry-specific anchoring before hanging the leaf.
- Santa Ana wind damage. Seasonal winds put sudden lateral stress on large ornamental swing gates, bending hinges and stripping operator gears. We size hinges and operators for wind load, not just gate weight. A gate that holds fine on a calm day can fold in a wind event if the hardware was undersized.
Pricing for Gate Installation in Beverly Hills, CA
Gate installation in Beverly Hills runs higher than surrounding cities because the permit path, architectural review, and custom fabrication all add steps. A standard single swing driveway gate with a new operator typically runs $4,800-$9,500. A double gate on original masonry pilasters, with custom forged hinges and masonry anchoring, lands between $9,000-$18,000. A sliding gate on a graded Trousdale driveway with a high-torque operator and brake runs $7,500-$15,000. Pedestrian gates matching existing ironwork start around $2,800-$6,000. Every quote is written and agreed before any work starts. The price we quote is the price you pay. Call (323) 677-4063 for a free estimate and we’ll walk the site with you before we hand you a number.
We Also Serve Cities Near Beverly Hills
We work throughout the Westside and into the Valley: Beverly Hills, West Hollywood, Studio City, Culver City, and Sherman Oaks. If you’re a few blocks over the city line, the same crew, the same warranty, and the same published pricing apply. We schedule Beverly Hills jobs around your HOA review timeline, not the other way around.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Beverly Hills
Yes, in most neighborhoods you need both HOA architectural approval and a city permit through Beverly Hills Building & Safety before any gate installation work begins. The HOA reviews style, height, material, and finish for consistency with the neighborhood’s established character. We’ll prepare submittal drawings and coordinate with your management company so the review moves without you chasing paperwork. Call (323) 677-4063 and we’ll outline the exact steps for your street.
Beverly Hills is an independent municipality with its own Building & Safety Department, so Los Angeles County rules don’t apply here. Every gate installation, including a like-for-like operator swap, must be permitted through Beverly Hills City Hall. Out-of-area contractors get this wrong constantly, and the project stalls when the inspector shows up. We handle the permit as part of the job. Call us and we’ll walk you through the exact path.
Yes, we fabricate custom leaves on site to match the ironwork, patina, and proportions of your original gate. Many Beverly Hills gates from the 1920s and 1930s are one-of-a-kind, and stock replacements don’t exist. We weld in your driveway, match the scrollwork, and hang the new leaf to match the existing one. Bring us a photo and we’ll tell you what’s possible before you spend anything.
A high-torque slide gate operator with a grade-compensating brake is the only setup we spec for Trousdale slopes. Flat-ground motors overheat and fail prematurely on 15-20% grades. We also run a dedicated power circuit for steeper lots, because a shared circuit with landscape lighting causes voltage drops that burn out control boards. Call (323) 677-4063 and we’ll evaluate your grade and give you a written recommendation.
Usually, yes. The hinge post is where the sag starts, especially on original brick or stone pilasters that were never reinforced for modern gate loads. Fix the panel without the post and you’ll fix it twice. We reinforce the pilaster with masonry-specific anchoring, then true the gate on the repaired post. Show us where it scrapes and we’ll show you where it’s failing. Call us for a free site look.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Beverly Hills since 2001.