Linear Gate Parts & Welding Nationwide | Gatewood Fence & Gate

Linear Gate Parts & Welding in West Hollywood: What to Know First

We’re Gatewood Fence & Gate, an independent Linear gate service provider in West Hollywood. Most Linear gate parts and welding jobs take us one visit, and the majority of owners pay between $140 and $480 depending on what actually failed. We quote the price before any work starts, in writing, and that’s the price you pay. If you own a Linear gate in West Hollywood and it’s sagging, grinding, or refusing to close, call (323) 677-4063 and Hal will talk you through what’s happening. This page is for Linear owners who want to know why their gate failed and what a real fix looks like.

Call (323) 677-4063

How Linear Products Fail - and How We Fix Them

Linear street gates in West Hollywood see the same thing every hillside driveway deals with: gravity working against the hinges, morning marine layer working against the metal, and a motor board that gets asked to move a gate the post has already given up on. Here’s what we actually see on Linear jobs.

• Linear SL series slide gates losing the track alignment. The SL series uses a chain-and-idler rig under the frame cover. When the concrete or pavers shift even a quarter inch, the idler pulley cants and the chain starts walking off the sprocket. The gate doesn’t need a new motor. It needs the track bed inspected, the idler bracket re-set square, and the chain tension brought back to spec. We do that on site.
• Hinge post fatigue on Linear swing gates. Swing gates hang every pound of panel mass off the hinge post, and in West Hollywood the soil on the steeper lots dries out and settles with the seasons. So the post leans, the hinges then carry the load at an angle, and the leaf tears or the hinge welds crack. We set the post true first, then weld the hinge repair. Fix the panel without the post and you’ll fix it twice.
• Lower rail rust-through on welded steel Linear panels. The lower horizontal rail sits closest to the splash line and traps moisture. On Linear residential swing panels, that rail is often the first piece to rot from the inside. Since we weld on site, we cut out the section, replace the rail stock, and re-attach the pickets rather than telling you the whole panel is junk. That’s a $200-to-$400 repair instead of a $1,800 replacement.
• Latch-and-lock misalignment on Linear drive gates. When the gate sags, the latch post and the latch itself stop lining up. The board then shows a fault because the lock reports “not closed” every time the gate cycles. We re-locate the strike plate, shim the latch housing square, and re-set the closed stop so the lock engages clean rather than binding against the post.
• Linear actuator arm stress cracks at the weld base. The ram-style actuators on Linear swing models push against a welded tab on the gate frame. Over years of cycling, that tab flexes at the weld root and the metal starts to crack. We grind the old weld down clean, reinforce the tab gusset, and re-weld it. It’s one of the most common Linear-specific weld repairs we do in West Hollywood.

Our Linear Gate Parts & Welding Process

1. 1
   You call and describe the problem. Hal answers, asks what the gate is doing, what the keypad or remote is showing, and whether it’s grinding, hesitating, or dead. That tells us a lot before we ever leave the shop.
2. 2
   We inspect the gate at your place. We check the panel, hinges, posts, rollers, latch, and the Linear board. We look for what shifted, not just what gave up.
3. 3
   We give you a written price for the repair. Upfront, before any work starts. If we can weld it rather than replace the panel, that’s what we recommend.
4. 4
   We do the repair and welding on site. The gate stays in your driveway. We cut, weld, fit, tighten, and re-set whatever failed, using OEM Linear parts when the board or actuator calls for spec, and quality aftermarket steel where the weld is the point.
5. 5
   We run the gate through a full cycle test, at least a half-dozen clean operations. If it doesn’t cycle clean, we’re not done.
6. 6
   We hand you the 90-Day Done Right Promise in writing. If something’s not right, one call brings us back, no runaround.

What Linear Gate Parts & Welding Costs in West Hollywood

Line-item pricing keeps the job honest. Here’s what Linear owners in West Hollywood typically pay with us:

• Hinge replacement - $45-$95 per hinge, plus a small weld time charge, usually 1-2 hours
• Post replacement or post reset - $280-$650 depending on concrete depth and access on the hillside
• Rail repair (cut, section, weld) - $220-$480
• Gate roller replacement - $65-$180 depending on whether the roller is welded in or bolted
• Custom welding for actuator tabs, latch plates, gate interior brackets - $85-$160 per hour
• Latch and lock rebuild or re-align - $90-$280

What moves the price is access on a slope, the amount of old weld to grind out, and whether the post needs to be re-set in concrete. We quote the job up front and that is the number on the invoice. Estimates are free. Call (323) 677-4063 and Hal will give you a straight price after he’s looked at it.

Why West Hollywood Homeowners Call Gatewood Fence & Gate for Linear Work

Hal Gatewood has been fixing gates in and around West Hollywood since 2001. His name is on the shop, his address is published, and the person who answers the phone at 2 a.m. is going to be able to actually help you. On a Linear job, we fix what’s failing rather than replacing the whole gate because replacement pays better. If your Linear actuator is fine and the weld is the problem, we weld it. If the hinge post shifted, we re-set the post. If the board is toast, we tell you that, and we install the OEM Linear part so the warranty on the board holds. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if the actual failure crosses a brand line - a board from one, an arm from another - we know what we’re looking at. Every job carries the 90-Day Done Right Promise in writing. And we mean it.

FAQs