Ghost Controls Gate Access Control Nationwide | Gatewood Fence & Gate

Ghost Controls Gate Access Control in West Hollywood: What to Know First

Ghost Controls gate access control repair in West Hollywood is what we handle regularly, from dead keypads and unresponsive remotes to phone entry systems that stopped ringing the house. Most Ghost Controls access problems get diagnosed same-day and fixed in one visit, with upfront pricing quoted before we touch anything. If you own a Ghost Controls opener and the access piece is acting up, call (323) 677-4063 and tell us what it’s doing wrong.

Call (323) 677-4063

If you have a Ghost Controls gate and the keypad stopped working after a rainstorm, or a remote that works only when you’re standing three feet away, this page is for you. We have been fixing these systems in West Hollywood driveways since 2001, and we have seen every failure mode this brand can produce.

How Ghost Controls Products Fail - and How We Fix Them

• Keypad memory loss after power interruptions. Ghost Controls keypads on the R Series and TSS1 lines are known to dump their entry codes after a brownout or hard power cycle. The owner enters the code, nothing happens, and they assume the motor died. It didn’t. Nine times out of ten, the access codes just need reprogramming and the keypad’s power supply needs checking. We fix that on-site in about 20 minutes.
• Receiver sensitivity drift. Ghost Controls remote receivers, especially on older AXDP and AXD models, become progressively deaf over time. The owner has to walk closer and closer to the gate until the remote works only from the driver’s seat. That’s a failing receiver board or a corroded antenna connection, not a dead battery. We test range with fresh batteries first, then pull the receiver and repair or replace the board depending on age and condition.
• Water intrusion at the keypad housing. West Hollywood gets morning fog, marine layer moisture, and occasional heavy rain cycles that beat on west-facing gates. Ghost Controls keypads are generally well-sealed, but the wiring behind the keypad, where the installer spliced the low-voltage line, is where corrosion starts. The keypad works intermittently, then quits after a wet stretch. We open the housing, clean and re-seal the connections, and the keypad comes back.
• Photo-eye alignment faults confusing the access system. When a Ghost Controls gate refuses to close and the keypad beeps but nothing moves, owners assume a control board failure. More often, the safety photo eyes got bumped out of alignment, or a shrub grew into the beam path. The access system sees a blocked path and refuses to operate. That’s a $75 to $140 alignment fix, not a $600 board replacement. We check the eyes before quoting anything.
• Worn-out actuator limit switches on swing gates. On Ghost Controls swing arm operators in West Hollywood hillside driveways, the limit switches inside the actuator wear down after years of constant cycles. The gate opens fine, closes halfway, then reverses. That’s not a programming issue. We replace the limit switch assembly, set the travel, and run the gate through a dozen full cycles to confirm it closes clean every time.

Our Ghost Controls Gate Access Control Process

1. 1
   You call. A live person answers, day or night. You describe what the access system is doing or not doing.
2. 2
   We show up. We arrive at your West Hollywood property, look at the gate, the operator, and the access components together. We test the keypad, the receiver, the photo eyes, and the wiring before touching a single part.
3. 3
   We tell you what it needs. We lay out the actual problem and give you a written price before any work begins. If the fix is a simple reprogramming, we say so and charge accordingly. We do not sell board replacements for keypad problems.
4. 4
   We repair. We use genuine Ghost Controls parts when the part is still in production and priced reasonably. For discontinued boards or limit switches, we use quality aftermarket equivalents that meet the same specs. We tell you which is which before we install anything.
5. 5
   We test. The gate cycles at least a half-dozen times, the keypad accepts the code, the remote works from the street, and the safety edges and photo eyes do their job. We don’t leave until it’s working right in front of you.
6. 6
   We stand behind it. Every job carries the 90-Day Done Right Promise in writing. If something isn’t right, one phone call brings us back. That’s the whole promise, plainly stated.

What Ghost Controls Gate Access Control Costs in West Hollywood

Your price depends on whether the Ghost Controls system is a newer R Series or an older AXD-generation model, how accessible the wiring is, and whether we are replacing one part or repairing several. Whatever the number, you get it in writing before we start. Estimates are free, and we don’t change the price at the door. Call (323) 677-4063 for an exact quote on your system.

Why West Hollywood Homeowners Call Gatewood Fence & Gate for Ghost Controls Work

Hal Gatewood has been fixing gates in West Hollywood since 2001, and he still answers his own phone most days. The name on the shop is the name on every invoice. When our crew shows up for a Ghost Controls access job, the person doing the work knows this brand’s quirks, from the keypad memory faults to the receiver sensitivity issues that other shops misdiagnose as motor failures. We also service LiftMaster, Mighty Mule, and DoorKing, which matters when a homeowner has a Ghost Controls opener but a LiftMaster keypad some previous installer cobbled in. We figure out what’s actually there, not what the label says should be there.

The 90-Day Done Right Promise is written on every job we hand you. It is not a phone-tree reassurance. If the access system misbehaves within 90 days of our repair, we come back. No runaround. We also weld on-site, which matters when a Ghost Controls swing arm operator has pulled loose from a rusted gate post and the post needs a repair plate before the access control will ever work reliably.

FAQs