Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Repair in West Hollywood: What to Know First
FAAC gate repair in West Hollywood typically runs between $240 and $680 depending on whether we’re chasing a sensor fault, a hydraulic leak, or a fried control board, and most jobs are done in a single visit. We’re an independent FAAC service provider - not affiliated with the manufacturer - which means we tell you the truth about what’s worth repairing and what isn’t, without a sales quota breathing down our necks. If you’ve got a FAAC gate acting up in the hills above Sunset or down in the flats near Santa Monica Boulevard, call (323) 677-4063 and a live person picks up. That’s us. Hal Gatewood answers his own phone, and he’s been fixing FAAC gates in West Hollywood since 2001.
This page is for the homeowner who owns a FAAC swing or slide gate and needs it working again without getting talked into a $3,000 replacement that wasn’t necessary. We’ll walk through how FAAC gates actually fail, what it costs to fix them, and why the repair usually beats replacement.
How FAAC Products Fail - and How We Fix Them
FAAC makes a solid gate operator. The hydraulic 400 series and the newer 770 electromechanical line show up all over West Hollywood, and each has its own personality when things go wrong. Here’s what we see drive after drive:
- FAAC 400-series hydraulic pump whine with sluggish movement. The hydraulic oil breaks down over years of West Hollywood sun exposure heating the pump housing. The gate still moves, but it sounds tired and labors in the morning. We flush the system, replace the oil, and often save the pump itself. Other companies quote a full operator swap because they don’t want to touch hydraulics. We’ve been inside these pumps since 2001.
- FAAC 770 and E024S control board capacitor failure. These boards run hot, especially mounted in direct afternoon sun on a southwest-facing gate near Doheny Drive. The symptom is specific: the gate opens fine but stops mid-close and reverses for no reason. That’s not a sensor alignment issue, it’s a capacitor on the board telling the motor it’s drawing too much current. We replace the capacitor and resolder the connection, which costs a fraction of a new board.
- Photocell faults on FAAC swing gates after rain. West Hollywood gets enough damp mornings and the occasional downpour that moisture creeps into the photocell housings. The gate refuses to close because it thinks something’s in the way. Sometimes it’s a bad cell, sometimes it’s just corrosion on the wiring terminals. We test before we replace, because a good pair of FAAC photocells isn’t cheap and a dirty terminal isn’t a dead cell.
- Gate leaf sag on FAAC 400-series heavy swing gates. Here’s a thing nobody tells you: FAAC operators will keep pushing a gate long after the hinge post has started leaning. The operator wears itself out fighting a geometry problem. A gate sags in the hinge post, not in the middle - and that is where we start. We weld and reinforce the post on site, rehang the leaf, and then set the FAAC limits correctly. Fix the panel without the post and you’ll fix it twice.
- Receiver range loss on FAAC 433 MHz remotes. Owners assume the remote’s dying. Usually the receiver antenna has been pinched or the receiver board has come loose from its mount inside the housing. We find this on FAAC systems installed before 2010 all over the hillside streets above Fountain Avenue. We remount the board, check the antenna, and test range from inside a car with the engine running - because that’s when it actually has to work.
Our FAAC Gate Repair Process
This is how a FAAC job goes at our shop, from the first call to the last test cycle:
- 1
You call (323) 677-4063. A real person answers, day or night. You tell us what the gate’s doing wrong, and we’ll often give you a straight read on the phone before we even roll out. Tell me what it’s doing wrong and I’ll tell you what it actually needs - give me your number and I’ll call you back myself.
- 2
We show up and listen first. That means watching the gate cycle, putting hands on the hinge posts, pulling the cover off the operator, and checking the FAAC diagnostic LED sequence. We don’t quote until we’ve looked.
- 3
We make one of two calls: OEM or quality aftermarket. If the part’s under warranty or it’s a safety item like a control board, we recommend FAAC original parts. If it’s a hinge bracket or a weather seal, we’ll tell you when a good aftermarket equivalent does the same job for less money. You decide, with real numbers in front of you.
- 4
We do the repair right there in your driveway. Hal welds on site. If the post needs reinforcement or a bracket snapped, you won’t watch your gate get hauled off on a flatbed. No trip charge inside the county, and the price is agreed before any work starts - always.
- 5
We cycle the gate a half-dozen times minimum. Not once, not twice. Six times, including one full stop-and-reverse test. Hal genuinely cannot walk away from sloppy work somebody else left behind, and he won’t call the job done until the gate cycles clean every single time.
- 6
You get the 90-Day Done Right Promise in writing. Not a verbal “call us if anything.” It’s stamped on the invoice. If it’s not done right, we make it right. One call brings Hal back, no runaround.
What FAAC Gate Repair Costs in West Hollywood
Straight numbers, because that’s how we quote:
- Photocell or safety edge replacement: $180-$290
- Diagnostic visit and limit/force adjustment: $110-$190
- Control board repair (capacitor, relay, solder work): $220-$450
- Full control board replacement (OEM FAAC): $480-$780
- Hydraulic oil flush and pressure adjustment (400 series): $240-$390
- Hinge post reinforcement with on-site welding and gate rehang: $450-$900
- Full FAAC operator replacement (labor included): $1,400-$2,600 depending on the series
What moves the price: the age and model of your FAAC operator, whether the hinge post needs welding, and whether we’re repairing a board or replacing it. What doesn’t move the price: hidden fees, trip charges inside the county, or a phone quote that changes when we arrive. Estimates are free, and you get the number in writing before anything gets unbolted. Call (323) 677-4063 and we’ll give you an honest read over the phone.
Why West Hollywood Homeowners Call Gatewood Fence & Gate for FAAC Work
Most of our regulars in West Hollywood found us after another company quoted a full gate replacement for something that took us ninety minutes to fix. That’s not marketing talk - it’s the whole reason Hal started putting his name on the shop instead of working under somebody else’s logo. We repair what other companies want to replace. We weld on site so the gate stays in your driveway. Hal’s name is on the truck, on the invoice, and on a shop you can drive to and look him in the eye. We’ve been at this since 2001, and we service nine major brands - so if you’ve also got a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing operator on the property, one call covers it. The 90-Day Done Right Promise is in writing on every job, a live person answers 24/7, and if you’re a senior or a veteran you get 10% off, permanently. Not a coupon. Just how we do it.
FAQs
No - as an independent FAAC service provider, our repairs don’t void your original warranty, and we’re careful to use OEM parts on any FAAC component still under coverage. If the operator’s out of warranty, we talk through whether an OEM or quality aftermarket part makes sense for your budget and how you use the gate. Either way, you’ll know the trade-off before you spend a dollar. Call (323) 677-4063 and we’ll walk you through it.
Most FAAC gate repair calls in West Hollywood are handled within 24 hours, and emergency no-open or no-close situations get same-day priority when you call before noon. We don’t promise a window we can’t keep. You’ll get a real time from a real person, and the person who shows up will be the person who quoted the job. If your gate’s stuck open right now, call (323) 677-4063.
We source the parts. We have supplier relationships for FAAC OEM boards, hydraulic pumps, photocells, and remotes, and we can usually have what your gate needs within one to three days if it’s not already on the truck. You won’t be told to go find a part number online and hope for the best. We handle the parts, the diagnosis, and the install - and we stand behind all of it with the 90-Day Done Right Promise.
It depends on what failed, and we’ll tell you straight. If the hydraulic pump on a 400-series is still tight and the hinge post hasn’t shifted, a $300 flush and adjustment can buy you years more service. If the control board’s gone and the post needs welding and the receiver’s intermittent, sometimes the honest answer is that the money’s better spent on a new operator. We’ll show you the numbers side by side and let you decide - no pressure, no quota. Call (323) 677-4063 for an honest assessment.
Yes. We work on FAAC slide gate operators including the 844 and 884 series, and the common failures there are different: track wear, v-wheel breakdown, limit switch drift, and gearbox oil leaks. The diagnosis process is the same - we watch the gate move, find where it’s laboring, and fix that. We don’t throw parts at a problem hoping one of them works.
Call Gatewood Fence & Gate for FAAC Repair in West Hollywood
If your FAAC gate is acting up anywhere in West Hollywood - the hills above Sunset, the streets off Santa Monica Boulevard, the driveways near Laurel Canyon - call (323) 677-4063. You’ll get a live person, an honest read on what’s wrong, and a free estimate before any work begins. The name is on the shop, and the shop is down the road - that is the oldest accountability there is. Hal Gatewood has been fixing FAAC gates in West Hollywood since 2001, and he’ll be the one walking your driveway.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving West Hollywood and nearby areas.