Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterDoorKing Gate Parts & Welding in West Hollywood: What to Know First
We handle DoorKing gate parts and on-site welding throughout West Hollywood, and most jobs are finished same day or within 24 hours once we see the gate. A hinge replacement or crack repair usually runs between $180 and $450 depending on the post condition and what the welder has to work around. We quote the price before any work starts, so the number you agree to is the number on the invoice.
This page is for West Hollywood homeowners and property managers with a DoorKing swing or slide gate that’s sagging, dragging, or refusing to close. If the operator still runs but the gate itself is coming apart, you’re in the right place. Call (323) 677-4063 and a live person answers, not a recording.
- We work on DoorKing gates as an independent service provider - not a manufacturer rep, just people who fix them every week.
- On-site welding means your gate stays in your driveway - we don’t haul it to some shop across town.
- Parts and labor are quoted before we start - and that quote doesn’t change at the door.
How DoorKing Products Fail - and How We Fix Them
- DoorKing 6002/6003 slide gate hinge brackets crack at the weld points. These swing-arm operators put constant torque where the arm meets the gate frame. Over time, that repeated stress fractures the bracket or the gate rail itself. We cut out the cracked section and weld in a gusseted replacement, then reinforce the surrounding frame so it doesn’t just crack again six months later. A weld patch without the gusset is a temporary fix, and we don’t do temporary.
- DoorKing 9024/9050 slide gates shear their rollers and ride rough on the track. West Hollywood driveways are built into hillside slopes, which means the track is never perfectly level. That adds side-load pressure to the rollers, and the cheap nylon wheels DoorKing ships from the factory wear flat on one side. We swap in steel or heavy-duty sealed rollers that tolerate off-level track, then align the gate so the wheels roll square instead of shoving sideways.
- DoorKing 9150 and 1601 operators keep tripping the entrapment sensor because the gate panel is bent. A gate that drags or catches on the track changes how fast the panel moves, and the operator’s safety board reads that as something blocking the path. The gate reverses, then tries again, and the homeowner thinks the operator is bad. We straighten or re-weld the panel frame, the gate cycles true again, and the sensor stops false-triggering. Operators often get replaced when the actual problem is the gate pulling against them.
- DoorKing hinge weld failures on heavy ornamental gates. A 14-foot wrought-iron drive gate weighs a lot more than DoorKing’s hardware was sized for. The top hinge takes that weight through the post, and eventually the hinge plate tears loose from the gate frame or the post starts leaning. We weld the hinge back and brace the post, or replace the post if it’s rusted from the inside. Fix the panel without the post and you’ll fix it twice - that’s a West Hollywood constant.
- DoorKing gate lock and latch damage after a windstorm. Santa Ana winds slam gates against their stops. The latch catches the strike plate too hard, bends or snaps the lock mechanism, and then the gate won’t stay closed. We weld in a heavier strike plate, replace the latch with something that handles the West Hollywood wind load, and align the gate so it closes with a thunk instead of a bang.
Our DoorKing Gate Parts & Welding Process
Here’s how a typical DoorKing job goes from your first call to the gate cycling clean.
- 1
You call, a person answers. Hal or one of his crew picks up the phone. You tell us what the gate is doing wrong, and we tell you whether it sounds like a weld issue, a parts issue, or both. If we need to see it, we set a window that same day or the next.
- 2
We inspect the gate in person. A sagging gate tells us where the failure is before we touch a tool. We check the hinge posts, the welds, the rollers, and the operator connections. Show us the gate closing on its own and we’ll show you where it’s failing.
- 3
We price the repair before we start. If it needs a new hinge, we quote it. If it needs a weld and a replacement roller, we quote both. If the repair is over $200, remember we take $40 off. Either way, you know the number before the welder gets warm.
- 4
We do the work on-site. For welding, that means the gate comes off its hinges or gets braced in place, the failed section gets cut out, and the new piece goes in with a proper weld, not a spot-tack. For parts, we use OEM DoorKing when it matters for compatibility and aftermarket when it’s genuinely better - like steel rollers instead of the factory nylon.
- 5
We test the gate through a full cycle, then test it again. Hal will not leave a gate until it opens and closes clean a half-dozen times. If the operator is fighting the gate, we fix that too while we’re there.
- 6
You get the 90-Day Done Right Promise in writing. If it’s not done right, you call, and we come back. That’s been the rule since 2001.
What DoorKing Gate Parts & Welding Costs in West Hollywood
| Job | Typical Cost | What Affects It |
|---|---|---|
| Hinge replacement (single, straightforward) | $180 - $320 | Post condition, gate weight, accessibility |
| Weld repair (cracked rail, torn hinge plate) | $200 - $450 | Size of the crack, how much grinding and prep |
| Gate roller replacement (pair, slide gates) | $150 - $300 | Track condition, roller type, gate weight |
| Post replacement with new hinge welds | $450 - $900 | Post size, concrete work, gate weight |
| Latch and lock replacement (incl. welding striker plate) | $160 - $380 | Gate material, wind exposure, type of lock |
| Custom welding - reinforcing, gusseting, frame repair | $250 - $800 | Scope of the repair, how many areas need work |
The big cost drivers are post condition and gate weight. A rusted-through post that has to be replaced costs more than a hinge swap, no way around it. We tell you what the gate actually needs and quote the work before we start. That applies to every DoorKing job in West Hollywood. Call (323) 677-4063 and we’ll give you a straight number.
Why West Hollywood Homeowners Call Gatewood Fence & Gate for DoorKing Work
Hal Gatewood has been fixing gates up and down these hillside driveways since 2001. He learned welding and metalwork at Los Angeles Trade-Technical College down on Washington Boulevard, and the name on the shop is the same name on the invoice. That’s not a marketing gimmick - it’s the oldest accountability there is.
Every DoorKing job we touch carries the 90-Day Done Right Promise. If something’s off, one call brings us back. No runaround, no arguing about what was or wasn’t included. That promise is in writing on every job.
We service nine major gate brands, so if your DoorKing feed is fine but a LiftMaster operator or a Mighty Mule or Ghost Controls unit is acting up, the same person can handle both while they’re on site. West Hollywood properties run a lot of different equipment, and a gate person who only knows one brand is the wrong person to trust.
And we answer the phone. Not a call center, not a chatbot, not a voicemail that says someone will get back to you in 2 to 3 business days. A live person picks up, day or night.
FAQs
Welding on the gate frame or hinge hardware doesn’t affect the DoorKing operator warranty, assuming the operator itself is untouched. The gate panel, hinges, and welds aren’t warrantied by DoorKing in the first place - those are site-installed components. If the repair involves wiring or the operator, we use OEM DoorKing parts and follow the install spec to keep any remaining manufacturer coverage intact.
Both. For anything electronic - circuit boards, loop detectors, entrapment sensors, keypads - we use OEM DoorKing parts, because knockoff electronics fail and then the gate does something weird. For mechanical parts like rollers, hinges, and strike plates, we often use aftermarket upgrades that outlast what DoorKing ships from the factory. The steel rollers we put in slide gates are a good example: they cost about the same and last twice as long on West Hollywood’s sloped tracks.
Most calls we can reach the same day, and welding jobs are usually done same day once we’re on site. A full post replacement or heavy custom work might take a day or two to schedule, but we’re not a company that puts you on next Thursday’s calendar for a call you made Monday morning. Tell me what it’s doing wrong and I’ll tell you what it actually needs - give me your number and I’ll call you back myself.
If the operator runs and the gate frame is still straight, repair it. Most DoorKing jobs we see are hinge failures, cracked welds, and bad rollers - all of which cost a fraction of a new gate. Replacement makes sense when the frame is rusted through in multiple places, the panels are beyond straightening, or the gate was undersized for the opening to begin with. We’ll give you an honest answer, and if replacement is the right call, we’ll tell you why and show you the numbers.
Both. We weld the gate frame, hinges, posts, rails, and latch hardware - and we service the operator that drives them. That’s the advantage of calling someone who understands the whole system. A welder who doesn’t know DoorKing electronics will fix the hinge and leave the operator misaligned. A technician who doesn’t weld will tell you to buy a new gate. We know both, and we fix whatever is actually broken.
Call Gatewood Fence & Gate for DoorKing Parts & Welding in West Hollywood
If your DoorKing gate is sagging, dragging, or pulling its welds apart, call (323) 677-4063 for a free estimate. A live person answers, 24 hours a day, and we’ll tell you over the phone what it probably needs and what it will cost. No trip charge inside the county, $40 off repairs over $200, and a permanent 10% discount for seniors and veterans. The name is on the shop, and the shop is down the road.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving West Hollywood and nearby areas.