Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterBFT Gate Parts & Welding in West Hollywood: What to Know First
We’re Gatewood Fence & Gate, an independent BFT service provider in West Hollywood that stocks, welds, and installs BFT gate parts the same week you call. Most hinge, rail, and post repairs run between $280 and $680 and we quote the price before any work starts, so there’s no surprise at the end. If you own a BFT swing or slide gate that’s sagging, grinding, or refusing to close, you’re on the right page. Call (323) 677-4063 and tell us what it’s doing wrong.
This page is for West Hollywood homeowners who want a straight answer about BFT gate parts and welding: what breaks, why it breaks, what it costs, and who can fix it without hauling the gate away. Hal Gatewood has been repairing BFT hardware in West Hollywood since 2001, and most of what we do is weld and realign what other outfits said needed replacing.
Key Takeaways
- We repair BFT gates on site with welding and OEM or quality aftermarket parts, usually within 3 to 5 business days.
- Most BFT gate part and welding jobs in West Hollywood run $280 to $680, quoted upfront in writing.
- We service all the common BFT lines found on West Hollywood driveways, from the older Phobos and Aries models to the newer Lux and Slideos systems.
- Every job carries our 90-Day Done Right Promise in writing. If it’s not right, we come back and make it right.
- Call (323) 677-4063. A live person answers, not a voicemail or a call center.
How BFT Products Fail - and How We Fix Them
BFT builds good hardware, but every line has its weak points. Here’s what we actually see on West Hollywood driveways, and what we do about it.
- Phobos swing gates: hinge post sag. The Phobos series has a heavy panel and, on hillside driveways like the ones we see in West Hollywood, gravity does its work over time. The gate sags in the hinge post, not in the middle. We pull the post back into plumb, weld in a new hinge plate or reinforcement gusset, and the gate cycles clean again. We don’t just tighten bolts and call it done, because a sagging post will strip those threads within a year.
- Aries series: cracked rail welds on slide gates. Aries slide gates often fail at the rail-to-post connection. It’s a stress point, especially on long runs. We grind the old weld down and weld the rail back with proper penetration, then add a support gusset so it doesn’t crack again in the same place. A patch weld on top of a failed weld is temporary; we cut it out and start fresh.
- Lux series: gate roller and track wear. The Lux line runs on rollers that eventually flatten or bind, especially if the track has any debris or sits on a slope that shifts with rain. In West Hollywood, hillside driveways with poor drainage wear rollers unevenly. We replace the rollers, true the track, and weld any support brackets that have worked loose.
- Slideos models: chain or rack loosening. The chain or rack on Slideos gates stretches and loses tension over time. Owners notice the gate stutters mid-travel or jerks at the ends. We inspect the rack alignment, tighten or replace the tensioner, and weld new rack mounts where the old ones have sheared off.
- Older BFT models: limit switch brackets snapping. On older BFT systems we see limit switch mounting tabs snap right off. The part is small, but when it goes the gate overruns and slams. We weld a new bracket in place, refit the switch, and set the limits so the gate doesn’t hammer itself at the end of travel. This one is a $90 weld instead of a $600 motor replacement, and it’s the kind of thing that gets missed by someone who doesn’t weld.
Our BFT Gate Parts & Welding Process
Here’s what happens when you call us about a BFT gate in West Hollywood.
- 1
You call (323) 677-4063. A live person answers and asks what the gate is doing, or not doing. We schedule a time that works, and we show up in that window.
- 2
Hal or one of his crew comes out and looks hard. We check the hinge posts, the welds, the rollers, the motor mount, and the travel path. We listen for the specific sounds different failures make, because a BFT operator that’s grinding isn’t the same as one that’s clicking.
- 3
We quote the price in writing. Before any work starts. If it’s a $40 weld, we say $40. If it’s a post replacement and welding, we say exactly what that costs. The quote doesn’t change after we start.
- 4
We decide on parts together. If an OEM BFT part is available and warranty-safe, we use it. If a quality aftermarket part makes more sense, we tell you why and what the savings are. We don’t hide the trade-off.
- 5
We do the work in your driveway. Welding, post replacement, roller swaps, rail repair, latch and lock fitting. The gate stays at your house.
- 6
We test until it cycles clean. Half a dozen cycles minimum, then we open and close it under load. You watch it work before we leave. Then the 90-Day Done Right Promise is yours in writing.
What BFT Gate Parts & Welding Costs in West Hollywood
| Job | Typical Price Range |
|---|---|
| Hinge replacement (single swing gate, welded) | $180 - $340 |
| Post replacement or reinforcement (existing gate rehung) | $310 - $680 |
| Rail repair and re-weld (slide gate) | $220 - $490 |
| Custom welding (brackets, gussets, limit switch tabs) | $90 - $300 |
| Gate roller and track replacement | $150 - $390 |
| Latch and lock fitting (manual or electric strike) | $110 - $260 |
What moves the price is the weight of the gate, how far out of whack the post or rail is, and whether we need OEM BFT parts or a quality aftermarket equivalent. We quote the number before we touch a tool. Take $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (323) 677-4063 for an exact quote. The estimate is free.
Why West Hollywood Homeowners Call Gatewood Fence & Gate for BFT Work
We’re not a national outfit with a call center three states away. Gatewood Fence & Gate is Hal Gatewood’s shop, and his address is published right here in our service area. He has been welding and repairing BFT gates since 2001, and most of his regulars in West Hollywood know him from the long driveways up near Laurel Canyon where a dead motor board or a snapped hinge can shut down your whole day. He learned metalwork at Los Angeles Trade-Technical College down on Washington Boulevard, and that foundation shows in every weld. Our crew services seven other major brands too (LiftMaster, Mighty Mule, Ghost Controls, DoorKing, and others), so when a mixed-property job comes up, we don’t pass it off to someone else. Every job carries the 90-Day Done Right Promise in writing. And when you call, a live person answers: not a voicemail, not a chatbot.
FAQs
No. We are an independent BFT service provider. That means we’re not tied to a factory parts catalog or a replacement-first sales target. We weld what needs welding, replace what needs replacing, and we tell you the difference. Being independent also means we can source quality aftermarket parts when an OEM part is backordered, without making you wait three weeks for a bracket.
Yes. We regularly source OEM BFT parts for Phobos, Aries, Lux, and Slideos gates through our distributors, and when a part is on backorder we offer appropriate aftermarket options at a lower price. We don’t install cheap knockoffs that’ll fail in six months. If we wouldn’t put the part on our own gate, we won’t put it on yours.
We weld on site, in your driveway, in West Hollywood. The gate stays on your property. We bring the welding rig, grinders, and materials to the job. That matters because a gate welded in place is a gate aligned to the posts, the slope, and the travel path it actually uses. Call (323) 677-4063 and we’ll schedule a time that works.
A single hinge replacement or rail re-weld typically takes 2 to 4 hours on site. A full post replacement with welding can take most of a day, depending on access and the condition of the surrounding concrete. We’ll tell you the timeline when we quote the job, and we don’t leave until the gate cycles clean.
Rarely. A gate panel is worth replacing when the panel itself is rusted through or structurally compromised. If the posts, rails, and hinges are solid, we can weld and realign. Tell me what it’s doing wrong and I’ll tell you what it actually needs. Give me your number and I’ll call you back myself. We’d rather repair a gate for $400 than replace it for $4,000, and that’s the truth.
Call Gatewood Fence & Gate for BFT Parts & Welding in West Hollywood
If your BFT gate is sagging, grinding, or not closing, call (323) 677-4063. We’ll give you a straight answer, a written quote, and a time we’ll be there. Hal Gatewood’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving West Hollywood and nearby areas.